Not available any more!!! archive items Pulse 2200 ARF 2200 mm KAVAN

item number: KAV8080

Order quantity {quantity} {pc}

Unit price: {PRICE} EUR

Quantity:

z.Zt. nicht lieferbar  Delivery time: z.Zt. nicht lieferbar

incl. 19% VAT. without tax
EUR 249,99 EUR 210,08
plus Shippingcost

Pulse 2200 ARF 2200 mm KAVAN KAV8080

Item number: KAV8080
EAN: 8596450016408

The Pulse has a wingspan of 2200mm and a beautiful coloured design which is easy to see in the air. This glider is equipped with a brushless motor (type C3548-750), a 50A controller (RAY G2 R-50SB) and has 6 servos. The Pulse is suitable for thermal fun and slope flying.

The construction of the model is improved from its predecessor: a well thought out mounting of the wings and the tailplane (see photo), a better processing of all parts. (EPO foam, small parts etc.).

Get ready for a good portion of fun. The new nimble and agile PULSE 2200 has an elegant scale construction like a modern glider, a wing with ailerons and flaps, a robust carbon reinforced EPO foam construction and thanks to a 600-800W brushless motor it has enough power for aerobatics and slope flying. The perfect recreational model for any advanced pilot to let off steam!

The fuselage of the model is made of highly durable EPO foam (extruded polyolefin) with solid internal reinforcements. A C3548-750 brushless electric motor with an 11x8-inch folding propeller and a RAY G2 R-50SB speed controller with a powerful BEC stabiliser, required to power 6 servos on board, is fitted in the nose. The canopy is removable and is attached with a pin at the front and a magnet at the rear. In the bow you will find enough space for the drive accumulator and the receiver. The elevator and rudder servos are located in the tail boom, the rudders are controlled by short straight linkages.

The wing of the model made of foam EPO consists of two parts with carbon strips, whose led out parts also serve as wing connectors and fit into the duraluminium housings in the fuselage. The wing halves are attached with a plastic screw. The ailerons (reinforced with carbon strips) and the flaps are always controlled independently with two servos with short straight wire rods.

The tailplanes are also made of EPO foam with carbon strips. The two-piece tailplane is attached to the fin with a carbon strip and a pair of screws to simplify assembly and disassembly.

The model is powered by a C3548-750 class brushless motor with 50A RAY G2 R-50SB regulator.

For power supply you need a LiPo 4-cell pack with a capacity of 2600-4000 mAh with a minimum load of 30C. Choose a specific type so that the correct centre of gravity position is as good as possible without further ballast.

You can also use a 6-channel RC set without special functions to control the model - in the basic version, ailerons and flaps are always connected to one channel with Y-cables only. Of course, it is ideal to use at least a 7-channel computer RC set, which allows independent control of ailerons and flaps by two servos, and a mix for the butterfly brake. In this case both ailerons control up and both flaps control down, which is possible with the affordable Hitec Flash 7 or 8, Radiolink AT9S or AT10II or Futaba T6K transmitters. In this case, the aileron and flap Y-cables in the fuselage must be replaced with four individual extension cables (15 to 30 cm).

Required accessories:
- Transmitter with receiver ( 5 channel)
- Drive battery Lipo 4S 2600-4000mAh

Technical data:
- Length: 1272mm
- Wingspan: 2200mm
- Weight: 2250g
- Aircraft type: Electric glider
- Version: ARF (Almost Ready to Fly)
- Material: Foam
- Type of drive: Electric
- Motor type: Brushless

Scope of delivery:
- Ready to fly model with built-in motor, propeller, controller, 6 servos and a manual.

Customers who bought this product also bought:

Already seen?

Retractable landing gear for gliders

EUR 208,00
incl. 19% MwSt

Turnbuckles M3 brass bright nickel

EUR 3,95
incl. 19% MwSt

1/10 Metal leaf spring hitch mount

EUR 69,99
incl. 19% MwSt