F7035 T8FG R6008HS 2,4 GHz

Robbe F7035 T8FG R6008HS 2.4 GHz

FASST Futaba Advanced Spread Spectrum Technology =

Fully expanded 8-channel computer system of superior quality with integrated 2.4 GHz FASST technology. The FASST system is a Spread Spectrum system with frequency hopping (FHSS). It may therefore transmit a maximum power of 100 mW EIRP, giving it ample reserves even for large-scale model aircraft and jets.
No co-channel interference, almost imperturbable, insensitive to electromagnetic pollution.

The central point is the high resolution of 128 x 64 dot graphic display with background lighting which makes for easy reading.
The elegant and simple design of the system is made possible by the new Cap-Touch system. Non-contact sensors that simulate a 3D hotkey, a smooth, sealed surface devoid of projecting controls.
Easiest programming in conjunction with the graphical user interface, menu structure and operation was taken over by the plants largely FX30/FX-40.
The software is available in 8 languages: German, English, French, Italian, Spanish, Czech, Russian or Dutch.
Special precision dual- axis stick units with digital trims and trim value memory. Particular emphasis was placed on the feeling of control when driving through the center position. Experience the new feeling of control.
The side-mounted rotary controls provide a practical means of operating supplementary functions without letting go of the sticks.
The plant has a total of 10 channels (8 and Prop 2 switching channels), where the channel order is arbitrary.
The transmitter has four analogue rotary controls and eight switches already fully equipped and requires no additional accessories. For almost all functions of the switches and the controls are freely selectable.
Comprehensive software provides also for functionally-oriented engine, glider and helicopter models, all necessary functions.
Plenty of freely programmable mixers are available with 5-point curves for setting up very complex mixer functions.
Integral Trainer system with individual function transfer. User-configurable channel assignment of students to teachers.
O ver the SD card can be put in the software of the system at any time by the user up to date.
20 model memory internally, infinitely expandable via SD card - 2 GB per 3862 models.

General Features

8 proportional channels plus two switched channels
4 stick functions, 8 switches, 4 rotary encoders
2 hour meter, including one model memory
2 free adjustable stop watches, with memory function
Switchable display of big-timers
Key Lock
Model selection, model 20 internal memory, expandable up to 3862 models using optional SD card (2 GB)
Memory model direct from the Start screen
Trim values are displayed in step or% reduction by zero-trim memory.

System functions

Trainer mode with individual function transfer and mix mode
Trainer function and virtual channels, 8 or 12 channel mode
User-configurable channel assignment of students to teachers
Hardware-reversal switch for all donors and
Stick Mode Setting 1-4
User name with 10 characters
Language English, German, French, Italian, Spanish, Czech, Russian or Dutch.

Basis functions

Graphical servo monitor with neutral and servo test
Model selection and copy function, model name with 10 characters
Choice of model type, engine model, glider, helicopter #
General frequency switching / switching and modulation France 7 / 12 channel.
Freely selectable output order for channels 1-8
Freely selectable transmitter controls - and trimmer selection for all functions
Freely selectable transmitter controls and trimmers selecting and virtual channels.
For all control donors (including switches, etc.) freely selectable trimmer selection
Digital stick trims, optionally with normal or ATL (asymmetrical) trim function. Alternatively, the group mode (effective in all flight modes) or single mode (effective only in relevant flight mode).
Free encoder assignment for switching channels 9 + 10
Servo center offset for channels 1-8
Servo reverse for channels 1-10
Failsafeeinstellung, Channel 3 (gas) in 7- channel mode, all channels in multi mode.
Travel adjustment with Limit function (ATV) for the 8 proportional channels
Endpoint with limiter setting for channels 1-8
Engine-off function
Idle 2
Trim step adjustment

Motor functions model
Comprehensive mixer menus for models with up to 4 wing servos. Besides the choice of wing type can also select from the following tail variants: normal, separate elevators with aileron function (ailvator) and V-tail. Deltas and powered flying wings with 2 .. 4 wing servos are available. These mixer menus are already on call to suit the model, pre-programmed with all the requisite mixer functions.

5 freely assignable and switchable Dual Rate / Expo settings.
5 free programmable mixer or 5-point linear curve per model memory, either with / without trim and offset.
5-point throttle curve
Speed adjustment for throttle servo
Aileron differential
Spoiler Mixer (flaperon)
Mixing height spoiler (flaperon)
Mixer side-cross
Page-level mixer
Snap roll mixer
Mixture adjustment
Gyro setting
Mixer motor, for two-stage switching of motors with individual speed adjustment for level 1 / 2 and back and back.

Functions sailors
Also for model gliders are extensive mixer menus for models with up to six wing-mounted servos. Available with or without power. Besides the choice of wing type can also select from the following tail variants: normal, separate elevators with aileron function (ailvator) and V-tail. Flying wings with 2 wing servos .. 6 to choose from. These mixer menus are pre-programmed with all the requisite mixer functions.
5 flight modes per model memory, with prioritization and adjustable switching delay. With logic switching function.
5 free programmable mixer or 5-point linear curve per model memory, either with / without trim and offset.
Aileron differential
Travel adjustment Flaps
Mixer cross-camber
Mixer cross-site
Spoiler mixer camber
Mixing height spoiler
Mixer-camber height
Mixer side- cross
Butterfly mixer with offset and delay adjustment
Butterfly mixer - Height
Mixer trim mix for aileron, rudder and elevator, with speed adjustment and FZS-switching delay.
Gyro setting
Mixer motor, for two- stage switching of motors with individual speed adjustment for level 1 / 2 and back and back.

Functions helicopter
The helicopter mixer menus differ basically in the swashplate control. All classical controls such as H1, HE3 (90 °), HR3 (120 °), H-3 (140 °), H4 and H4-X (45 °) are integrated. A special feature is the adjustable pushrod for the H3 and H4 types. This eliminates the usual way with larger displacements or asymmetrical, which can cause servo to permanent damage. Also, the elevator function to be adjusted in speed to the delay difference in the HR/N3 120 ° to avoid linkage.
Swashplate mixer
Swashplate ring mixer
5-point pitch curve normal, idle 1,2,3, auto-rotation. With logic switching function.
5-point throttle curve normal, idle 1,2,3, auto-rotation. With logic switching function.
Autorotation
Swashplate mixer (virtual rotation)
Swashplate mixer? Gas (linear / Center)
Heck mixer? Gas (linear / Center)
5-point pitch- tail mixer, normal, idle 1,2,3, auto-rotation. With logic switching function.
Mixture adjustment
Rotary mixer with 3 rates and fine trim adjustment
Speed controller with 3 rates and fine trim adjustment

Technical data:
Dimensions: 175 x 175 x 55 mm
Weight: 820 g
Frequency Band: 2400.00 MHz
Channel spacing: 2048 kHz
Current consumption: 220 mA
Power: 7.2 volt NiMH battery
Features: 8 / 10 Servos
more Specifications:
Compatible with the receivers R6004FF, R606FS, R6106HF / C, R607FS, R617FS, R608FS, R6008HS, and R6014FS R6014HS.

Delivery:
1 Channel 2.4GHz FASST T8FG
1 receiver R6008HS FASST 2.4 GHz
1 Transmitter battery, 7.2 V NiMH 1700 mAh
1 AC charger Tx-Rx 170 / 150 mA
1 switch cable
1 screwdriver