AT10II TX + R12DS RX + telem. module 1RL0020

RadioLink transmitter AT10II with receiver R12DS + telemetry module 1RL0020

Item no.: RL0020

EAN: 6947470340424

12-channel RC set 2.4.GHz FHSS/DSSS with joystick, 8 switches, 5 rotary encoders. R12DS telemetry receiver. Memory for 15 models, acro mixer, glider, helicopter, up to 5 flight modes, freely assignable controls and switches, telemetry on the display.

AT10II is a 12-channel PC transmitter for hobby and sports modellers for convenient control of all current models: Acro motor models, gliders, helicopters, multicopters, cars and other land vehicles and ships. It has a practical housing that sits very comfortably in the hand and has a tried and tested ergonomic arrangement of the controls.

Controls: The main functions are controlled by precise cross sticks with adjustable force by means of neutralisation springs. It is possible to convert the throttle axis to the right or left. This allows you to select stick modes 1-4. The control sticks are adjustable in position. You can also buy long aluminium heads (with M3 thread). The digital trims have an acoustic signal of the step sequence and a graphic display of the positions on the screen. They are slightly off-centre and easy to reach. Additional proportional functions can be controlled by two buttons on the sides of the transmitter with mechanically locked centre position and three buttons in the centre above the main switch. 8 switches (including three three-way switches and one momentary two-way switch) can be used as channel switches, for switching flight modes or for switching mixers on and off. The control elements are freely assignable.

Transmitter power supply: AT10II can be powered by a variety of different batteries: 8 alkaline batteries in the supplied holder; NiMH battery pack with 8 cells (size AA, AA batteries) or 2-4 LiPo cells, LiFe, Li-ion; the battery voltage is shown in numerical and graphic form on the display, under-voltage warning is adjustable. We recommend our 9.6V NIMH cell sets with low self-discharge (Eneloop, RayLong), customised for the transmitters and equipped with a charging port.

Transmission system: AT10II uses the unique Radiolink technology with simultaneous DSS and FHSS frequency hopping for long range, reliability and excellent interference immunity. The system allows telemetry data to be transmitted from the receiver and displayed on the transmitter display.

User interface: The transmitter is programmed via a 3D programming wheel/button, two buttons and a mini cursor joystick together with an illuminated graphic LCD colour display. The display has adjustable contrast and a choice of "colour on black" or "colour on white" display modes to perfectly match the ambient light conditions.

Software: The software is a classic type with pre-programmed mixers and pre-programmed menus for different model types. AT10II has a memory for 15 models.

Operation menu has three basic screens: The home screen is used to operate the transmitter in normal mode - it shows the type and name of the selected model, the current flight mode, the type of receiver used, the digital trim positions, the timing data and, when using a telemetry receiver, also the receiver's supply voltage. The telemetry screen clearly displays the data of all connected telemetry sensors and modules, and the servo monitor screen provides a graphical representation of the servo movements across all channels.

Programme menu is always divided into two parts for clarity - The BASIC basic menu contains basic system settings of the transmitter, basic model settings (model type, assignment of controls and reverse switches, trim, sub-trim, dual rate reverse switch, dual rate deflections and exponential function, etc.) The Advance menu contains freely programmable mixers, model-specific mixers (throttle and collective curve, V-tail mixer, mixer for delta, etc.).

Pre-programmed model types:

- Glider (1 aileron + 1 flap)

- Glider (2 ailerons + 1 flap)

- Glider (2 ailerons + 2 flaps)

- Motorised acro model

- Helicopter

- Multicopter

Pre-programmed mixers and functions:

- Setting servo reverse switches

- Setting the end points of the deflections

- Subtrim

- Trim step size

- Dual rate deflections

- Setting the servo speeds

- Exponential progression of the deflections

- Motor off

- Safe freewheel

- Failsafe

- Gyro remote control for helicopters and aeroplanes

- Three timers

- Teacher-student

- Servo monitor

- Flaperon

- Elevon

- V-tail

- 8 freely programmable mixers (4 linear, 4 s 5-point curve)

- Airbrakes

- Control of the glider's flaps

- Mix aileron rudder

- Mix elevator flaps

- Mix aileron flaps

- Elevator with 2 servos

- Flap trim

- Delta mixer

- Snap Rolls

- Throttle curve (for motorised aircraft)

- Throttle delay

- Throttle curve (7-point for helicopters)

- Tail rotor curve (7-point for helicopters)

- Revo-Mix

- Swashplate mixer (8 types)

- Throttle mixer (for helicopters)

- Swashplate deflection limiter

- Trim and throttle collective when hovering

- Trim of high and low collective

- Autorotation

- Governor control

- Flight modes (up to 5 modes for gliders and helicopters)

- Flight modes for multicopters and drones

Micro USB socket is used to update the firmware with a PC.

Teacher-student socket is used to control models via a dual control system with two Radiolink transmitters connected via a teacher-student cable. AT10II can be used both as a teacher and as a student transmitter. The teacher transmitter can transmit all or selected channels to the student. It is also possible to transfer partial control to the student. In addition to the classic cable (1RL0058), a wireless connection can also be used via a receiver with PPM output, which is connected to the teacher-student socket of the teacher transmitter via a special adapter (1RL0056). The receiver is paired with the student transmitter.

Transmitter strap: AT10II can be attached to the centre hinge using the transmitter strap and worn around the neck. (sold separately) .

Telemetry: When using a telemetry receiver (R12DS, R9DS), the receiver voltage and signal strength of the receiver are shown on the transmitter display (with adjustable alarm threshold). After connecting the PRM-01 telemetry module, the voltage of the drive battery (1-6S LiPo) is also measured and displayed.

Compatible receivers:

- Telemetry, full range: R9DS, R12DS

- Without telemetry, full range: R12DSM Mini

- Without telemetry, limited range: R6DS, R6DSM Mini

Modulation/encoding: 2.4GHz FHSS / DSSS ; Channel quantity: 12 ; Weight (incl.8x AA NiMH Tx aku) [g]: 872 ; Power supply (8x AA alkaline battery) [V]: 12 ; Power supply (8x AA NiMH) [V]: 9.6 ; Power supply LiXX cells: 2 - 4

Technical data:

- Modulation/encoding: 2.4GHz FHSS / DSSS

- Number of channels: 12

- Weight (8x AA NiMH Tx battery) [g]: 872

- Power supply (8x alkaline AA battery) [V]: 12

- Power supply (8x AA NiMH) [V]: 9.6

- Power supply of LiXX cells: 2 - 4

The set includes:

- AT10II transmitter

- 12-channel telemetry receiver R12DS

- Telemetry module for measuring the voltage PRM-01 with cable

- Operating instructions