AMXFlight YAK-11 rot/weiß PNP 6S EPO Amewi 24100
Artikelnummer: 24100
EAN: 4260677953467
Description
The Yak-11 was designed and put into service in the 1940s specifically for the advanced flight training of fighter pilots. The experience of the war-tested Yak-1, -3, -7 and -9 single-seater fighter aircraft was incorporated into its development, so that their best features could be adopted into the Yak-11. The powerful, air-cooled radial engine with around 700 hp gave even better flight capabilities. The two-seat training aircraft was used by all member states of the Warsaw Pact as well as in the Middle East, Austria and China. The wingspan of this machine, which was manufactured primarily in Czechoslovakia, was 9.40 meters.
The AMXFlight YAK-11 is a very nice scale replica in red and white paint with all stickers that correspond to the original. The look and quality of the model are outstanding - the plane immediately impresses with its size with a wingspan of 1450mm, the massive fuselage and the huge 16 x 6E propeller. The YAK-11 comes out of the box as a PNP variant and all components such as servos, motor, controller, landing gear and landing flaps (spread flaps) are already installed. The assembly is simply limited to screwing the tail unit together and attaching the 2-part main surface. All components are screwed. Only the scale antenna behind the cockpit needs to be glued in. The voluminous fuselage is ideal for holding 6S LiPo batteries with a capacity of 5000mAh and the specified center of gravity of the model is therefore easy to adjust. The canopy is very generously designed and allows clean work inside the fuselage. The chassis is made with 5mm material thickness and active damping - it can therefore easily withstand the weight of the model as well as uneven take-off and landing areas. The spreader flaps significantly reduce the flight speed to make landing as easy as possible.
The model is very easy to fly and appeals to both advanced and experienced model pilots. With the recommended 6S LiPo 22.2V 5000mAh min. 30-40C, long flight times of up to 10 minutes are possible. The performance of the model is more than sufficient for dynamic aerobatics or fast, low overflights, for example. The latter appear particularly impressive due to the proportions of the model.
Features:
- Great optics (scale replica)
- Scale cockpit with pilot figure
- Very nice red/white paint job
- Quick release for the canopy
- Wooden inserts for clean storage of the battery and receiver
- Very good flight characteristics at any speed (slow to fast)
- Very high quality of material (EPO)
- Strong brushless motor (Potenza BL65 3D / 550KV)
- Large 80A regulator for 6S LiPo batteries
- Large 16 x 6E propeller
- High quality digital servos with metal gears
- Fully steerable tail wheel for full control on the ground
Technical data:
- Wingspan: 1450mm
- Length: 1300mm
- Weight: approx. 2500g (without battery)
- Main material: EPO
- Thrust: over 1:1
- Motor: Potenza BL65 3D / 550KV
- Controller: 80A ESC Brushless 6S with XT90 connector and BEC system for power supply
- Servos: 6x digital 19g MG
- Propeller: 16 x 6E High Performance Prop
- Electric retractable landing gear with full metal suspension and time delay when extending and retracting
Required accessories:
- Transmitter/receiver at least 6 channels
- Battery LiPo 6S min. 4500-5000mAh 22.2V min. 30-40C XT90
- Charger for LiPo batteries
- Tool
Scope of delivery:
- PNP model with all electronic components installed
- Small parts such as screws, scale antennas (optical tuning), tail skid and much more.
- Operating instructions (illustrated) DE/EN
EUR 329,00
incl. 19% MwSt
EUR 1.399,00
incl. 19% MwSt
EUR 319,99
incl. 19% MwSt